BOCA RESEARCH, INC. BOCA WINSTORM 56K PCI MODEM Card Type Modem, Fax Chip Set Unidentified I/O Options microphone, speaker out Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34, V.90, K56 flex Fax Modulation Protocol ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP2-4,MNP5, V.42, V.42bis Fax Class Class I & II Data Bus 32-bit PCI Card Size Half-length, half-height card [Image] CONNECTIONS Function Label Function Label Microphone CN1 Speaker out CN2 SUPPORTED COMMAND SET Basic AT Commands AT, A/ A, E, H, L, M, O, Q, S, T, V, X, Z &C, &F, &P, &V Extended AT Commands %Q S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12 Special Commands +MS Note: See MHI Help File for full command documentation. Proprietary AT Command Set DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DL Re-dial last number DP Pulse dialing enabled DS=n Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D"WXY" Optional method of denoting telephone numbers. Letters enclosed in quotes are interpreted as numbers according to the system found on a telephone keypad. D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D& Wait for credit card bong before continuing with the dial string D^ Toggles calling tone enable/disable D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D$ Wait for prompt tone detection function enabled. Waits for prompt tone for amount of time specified by the S7 command. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports modem model and speed I1 Reports ROM checksum I2 Tests and reports ROM checksum I3 Unidentified I4 Unidentified I5 Unidentified I6 Reports data connection information I7 Reports manufacturer and model information DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Command Function &D0 Modem does not respond to DTR &D1 Modem goes to command mode after DTR goes is off &D2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. GUARD TONE Type: Configuration Format: AT [cmds] &Gn [cmds] Description: Commands the modem to transmit a guard tone in V.22/V.22bis Note: Used primarily for international data transmission Command Function &G0 Guard tone disabled &G1 Guard tone disabled &G2 1800Hz guard tone enabled STORE ACTIVE PROFILE Type: Configuration Format: AT [cmds] &Wn [cmds] Description: Writes the values for the active profile into the non-volatile RAM Extended AT Commands AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD Type: Configuration Format: AT [cmds] %En [cmds] Description: Controls auto-retrain mode and fallback/fall-forward Command Function %E0 Auto-retrain disabled %E1 Auto-retrain enabled DSVD Type: Configuration Format: AT [cmds] –SSEn [cmds] Description: Controls the DSVD Command Function -SSE0 Disabled -SSE1 Enabled Special AT Commands DATA COMPRESSION Type: Configuration Format: AT [cmds] +DSn,m,o,p [cmds] Description: Controls the data compression Command Function n=0 Negotiated; no compression n=1 Data compression both directions, accept any direction m=0 Do not disconnect if V.42bis is not negotiated by the remote modem as specified in n o Specifies the maximum number of dictionary entries (2048 entries) which should be negotiated p Specifies the maximum string length (32bytes) to be negotiated ERROR CONTROL REPORING Type: Configuration Format: AT [cmds] +Ern [cmds] Description: Controls the whether or not the extended-format intermediate result code is transmitted from the modem to the DTE Command Function +ER0 Disabled +ER1 Enabled LOCAL FLOW CONTROL Type: Configuration Format: AT [cmds] +IFCn [cmds] Description: Controls the modem local flow control Command Function +IFC0 No flow control +IFC1 XON/XOFF on transmitted data +IFC2 Circuit 133 +IFC3 XON/XOFF on transmitted data with XON/XOFF characters being passed through to the remote modem. LOCAL RATE REPORTING Type: Configuration Format: AT [cmds] +ILRRn [cmds] Description: Controls whether or not the extended-format information text is transmitted from the modem to the DTE Command Function +ILRR0 Disabled +ILRR1 Enabled MANUFACTURER IDENTIFICATION Type: Configuration Format: AT [cmds] +GMIn [cmds] Description: Reports the modem manufacturer MODEL IDENTIFICATION Type: Configuration Format: AT [cmds] +GMMn [cmds] Description: Reports the modem model identification MODULATION REPORTING Type: Configuration Format: AT [cmds] +MRn [cmds] Description: Controls the modulation reporting Command Function +MR0 Disabled +MR1 Enabled REVISION IDENTIFICATION Type: Configuration Format: AT [cmds] +GMRn [cmds] Description: Reports the modem version, revision level, or date. VIDEO READY MODE Type: Configuration Format: AT [cmds] +Hn [cmds] Description: Controls the video ready mode Command Function +H0 Disable video ready mode +H16 Enabled video ready mode S(status) -REGISTERS FLASH DIAL MODIFIER TIME Type: Register Format AT [cmds] S29=n [cmds] Default: 70 Range: 0-255 Unit: .01 second Description: Time the modem will go on-hook upon receiving the ! dial modifier in dial string.